The optimum combination of hardness, strength and toughness is developed throughout the cross section of an engineering product made from steel, by means of hardening and tempering. This treatment consists of heating the work-piece to an appropriate hardening temperature, which is dependant upon the particular steel analysis involved, holding for sufficient time to ensure the whole work-piece is at temperature and then rapidly cooling it in a suitable medium (quenching). This medium can be air, oil, water, molten salt, fluidised bed or a pressurised inert gas, such as nitrogen. Selection of the quench medium is dependant upon steel analysis, component geometry, the heat treatment furnace used and the manufacturing stage at which hardening and tempering is carried out. The resultant temperature changes induce physical transformation of the steel, resulting in mechanical property changes.
Following quenching, the work-piece is in its hardest but brittle condition and therefore requires a further thermal treatment (tempering, or drawing), to produce the optimum balance of properties. This consists of re-heating the work-piece to a lower temperature and holding for a specific time. The choice of time and temperature depends upon the amount of tempering or ‘softening back’ the work-piece requires. Hardening of engineering steels (in the carbon range 0.3 to 0.55%, ranges between 800 and 900 deg.C.. Tempering is generally carried out between 400 and 700 deg. C. Tools made from higher alloy steels are also hardened and tempered but require significantly higher temperatures, up to 1300 deg. C. for hardening and multiple tempering treatments are often required.
For any steel analysis and quenching medium there is a section size, above which the work-piece will not satisfactorily through harden. This is known as the limiting ruling section and is the main design parameter that needs to be considered, in combination with the geometry and property requirements of the work-piece, when specifying a hardening and tempering treatment. As quench severity increases, as it does if air is replaced by oil, and oil is replaced by water, the limiting ruling section increases for a particular steel composition. However, the use of more severe quenching is limited in turn by the increased risk of distortion or cracking during quenching, due to the higher thermal stresses induced in the work-piece.
Although it can be applied to bars, forgings and castings, hardening and tempering is often left to a late stage of manufacture, in order to minimise manufacturing costs and maximise the properties produced. Often, the only post treatment operation is grinding. As a result, the environment within the furnace surrounding the work-piece has to be controlled, in order to prevent unwanted chemical changes, such as oxidation, decarburisation and scaling, adversely affecting the work-piece surfaces. For this reason Bodycote operate vacuum furnaces and controlled atmosphere pit and continuous furnaces, sealed quench furnaces and fluidised beds, all of which are suitable for hardening and tempering with complete control of surface chemistry.
The need for precise control of temperature and time, as well as environmental chemistry, has led to the application of computerised control systems for most types of furnace. This is a development that was pioneered in the UK by Bodycote and continues to be an important tool for both process improvement and cost control.
Care should be excercised during material selection, component manufacture and also when selecting a hardening and tempering method and facility. As with all heat treatments, the advice of the steel supplier and heat treater is best sought at an early design stage, if the attendant risks are to be minimised.
Here are the various Hardening & Tempering services available from Bodycote
Click on one to find out more...
> Flame
> Fluid Bed
> Furnace
> Precipitation
> Press Quenching
> Vacuum
> Atmosphere
> Water Quenching
> Oil Quenching
Bodycote Thermal Processing - Fremont, California Bodycote Thermal Processing 4240 Technology Drive Fremont CA 94538-6338 California |
| Tel: +1 510 492 4200 Fax: +1 510 492 4242 |
| E-Mail: skip.jones@bodycote.com |
| Main Contacts |
| Mr Skip Jones, General Manager skip.jones@bodycote.com |
| Mr Nils Kjell, Sales Manager nils.kjell@bodycote.com |
| Ms Lisa Mueller, Operations Support Adminstrator lisa.mueller@bodycote.com |
| Mr Dave Ochar, Regional Sales Manager, WG/CA dave.ochar@bodycote.com |
| Mrs Rhonalyn Sampaga, Quality Manager rhonalyn.sampaga@bodycote.com |
| Mr Kevin Button, Braze Engineer kevin.button@bodycote.com |
| Mr Todd Erkel, Regional Quality Manager todd.erkel@bodycote.com |
| Click here for Applications and the Plant Profile for Fremont > |
 |
Bodycote Thermal Processing - Gardena, California Bodycote Thermal Processing Werk Garching 355 West Alondra Boulevard Gardena CA 90248 California |
| Tel: +1 310 532 0419 Fax: +1 310 532 0088 |
| E-Mail: mark.johnson@bodycote.com |
| Main Contacts |
| Mr Mark Johnson, General Manager mark.johnson@bodycote.com |
| Mr Dave Ochar, Regional Sales Manager, WG/CA dave.ochar@bodycote.com |
| Mr John Ruffin, Quality Manager john.ruffin@bodycote.com |
| Mr Todd Erkel, Regional Quality Manager todd.erkel@bodycote.com |
| Click here for Applications and the Plant Profile for Gardena > |
|
Bodycote Thermal Processing - Huntington Park, California Bodycote Thermal Processing 3370 Benedict Way Huntington Park CA 90255 California |
| Tel: +1 323 583 1231 Fax: +1 323 589 1255 |
| E-Mail: chris.hall@bodycote.com |
| Main Contacts |
| Mr Chris Hall, General Manager chris.hall@bodycote.com |
| Mr Moses Casillas, Quality Manager moses.casillas@bodycote.com |
| Ms Starla Dixon, Office Manager starla.dixon@bodycote.com |
| Ms Debra Lovell, Customer Service debra.lovell@bodycote.com |
| Mr Dave Ochar, Regional Sales Manager, WG/CA dave.ochar@bodycote.com |
| Mr Skip Jones, Regional Operations Manager skip.jones@bodycote |
| Mr Krishna Cherukuri, Production Manager krishna.cherukuri@bodycote.com |
| Mr Todd Erkel, Regional Quality Manager todd.erkel@bodycote.com |
| Mr Bob Lehnen, Metallurgist bob.lehnen@bodycote.com |
| Click here for Applications and the Plant Profile for Huntington Park > |
|
Bodycote Thermal Processing - Rancho Dominguez, California Bodycote Thermal Processing 515 West Apra Street Rancho Dominguez CA 90220 California |
| Tel: +1 310 604 8000 Fax: +1 310 604 9959 |
| E-Mail: matt.alty@bodycote.com |
| Main Contacts |
| Mr Matt Alty, General Manager matt.alty@bodycote.com |
| Mr Randy Gualajara, Quality Manager randy.gualajara@bodycote.com |
| Ms Patty Flores, Office Manager patty.flores@bodycote.com |
| Mr Dave Ochar, Regional Sales Manager, WG/CA dave.ochar@bodycote.com |
| Mr Kevin Button, Braze Engineer kevin.button@bodycote.com |
| Mr Todd Erkel, Regional Quality Manager todd.erkel@bodycote.com |
| Click here for Applications and the Plant Profile for Rancho Dominguez > |
|
Bodycote Thermal Processing - Santa Fe Springs (Burke St), California Bodycote Thermal Processing 11845 Burke Street Santa Fe Springs CA 90670-2537 California |
| Tel: +1 562 693 7733 Fax: +1 562 693 8581 |
| E-Mail: paul.dymond@bodycote.com |
| Main Contacts |
| Mr Paul Dymond, General Manager paul.dymond@bodycote.com |
| John Palmer, Quality Manager john.palmer@bodycote.com |
| Mr Fred Viramontes, Plant Manager fred.viramontes@bodycote.com |
| Ms Connie Casillas, Office Support Adminstrator connie.casillas@bodycote.com |
| Mr Dave Ochar, Regional Sales Manager, WG/CA dave.ochar@bodycote.com |
| Mr Kevin Button, Braze Engineer kevin.button@bodycote.com |
| Mr Todd Erkel, Regional Quality Manager todd.erkel@bodycote.com |
| Click here for Applications and the Plant Profile for Santa Fe Springs (Burke St) > |
|
Bodycote Thermal Processing - Santa Fe Springs (Romandel), California Bodycote Thermal Processing 9921 Romandel Avenue Santa Fe Springs CA 90670 California |
| Tel: +1 562 946 1717 Fax: +1 562 946 8768 |
| E-Mail: manuel.granillo@bodycote.com |
| Main Contacts |
| Mr Manuel Granillo, General Manager manuel.granillo@bodycote.com |
| Mr Juan Espinoza, Plant Manager juan.espinoza@bodycote.com |
| Mr Mike Fobar, Customer Service Manager mike.fobar@bodycote.com |
| Mr Dave Ochar, Regional Sales Manager, WG/CA dave.ochar@bodycote.com |
| Mr Todd Erkel, Regional Quality Manager todd.erkel@bodycote.com |
| Mr Al Martinez, QC Manager al.martinez@bodycote.com |
| Terri Galvan, Office Manager terri.galvan@bodycote.com |
| Jacquelyn Winter, Metallurgist jacqui.winter@bodycote.com |
| Click here for Applications and the Plant Profile for Santa Fe Springs (Romandel) > |
|
Bodycote Thermal Processing - Vernon, California Bodycote Thermal Processing 2900 South Sunol Drive Vernon CA 90023 California |
| Tel: +1 323 264 0111 Fax: +1 323 268 9897 |
| E-Mail: raquel.musquiz@bodycote.com |
| Main Contacts |
| Ms Raquel Musquiz, General Manager raquel.musquiz@bodycote.com |
| Mr Leslie Loucks, Plant Manager leslie.loucks@bodycote.com |
| Mr Willie Ramirez, Metallurgist william.ramirez@bodycote.com |
| Ms Cori Garcia, Office Manager cori.garcia@bodycote.com |
| Mr Dave Ochar, Regional Sales Manager, WG/CA dave.ochar@bodycote.com |
| Mr Skip Jones, Regional Operations Manager skip.jones@bodycote.com |
| Mr Todd Erkel, Regional Quality Manager todd.erkel@bodycote.com |
| Click here for Applications and the Plant Profile for Vernon > |
|
Bodycote Thermal Processing - Berlin, Connecticut Bodycote Thermal Processing 675 Christian Lane Berlin CT 06037 Connecticut |
| Tel: +1 860 225 7691 Fax: +1 860 229 3891 |
| E-Mail: dennis.smith@bodycote.com |
| Main Contacts |
| Mr Sal Santangelo, Plant Manager sal.santangelo@bodycote.com |
| Mr. Dennis Smith, Reg. Operations Manager dennis.smith@bodycote.com |
| Mr Bob Sartori, Regional Quality Manager bob.sartori@bodycote.com |
| Mr Roger Fabian, Sales Manager roger.fabian@bodycote.com |
| Ms Denise Bouchard, Office Manager denise.bouchard@bodycote.com |
| Click here for Applications and the Plant Profile for Berlin > |
|
Bodycote Thermal Processing - South Windsor, Connecticut Bodycote Thermal Processing 45 Connecticut Avenue South Windsor CT 06074 Connecticut |
| Tel: +1 860 282 1371 Fax: +1 860 282 9020 |
| E-Mail: mike.sakelakos@bodycote.com |
| Main Contacts |
| Mr Mike Sakelakos, General Manager mike.sakelakos@bodycote.com |
| Mr Roger Fabian, Sales Manager roger.fabian@bodycote.com |
| Ms Tracy Darna, Office Manager tracy.darna@bodycote.com |
| Mr Dennis Smith, Regional Operations Manager dennis.smith@bodycote.com |
| Mr Bob Sartori, Regional Quality Manager bob.sartori@bodycote.com |
| Mr Greg Nugent, Quality Manager greg.nugent@bodycote.com |
| Click here for Applications and the Plant Profile for South Windsor > |
|
Bodycote Thermal Processing - Waterbury, Connecticut Bodycote Thermal Processing 130 Huntingdon Avenue Waterbury CT 06708 Connecticut |
| Tel: +1 203 755 9119 Fax: +1 203 597 0521 |
| E-Mail: dennis.smith@bodycote.com |
| Main Contacts |
| Mr Mike Cenotti, General Manager mike.cenotti@bodycote.com |
| Ms Eileen Sarajak, Office Manager eileen.sarajak@bodycote.com |
| Mr Dennis Smith, Regional Operations Manager dennis.smith@bodycote.com |
| Click here for Applications and the Plant Profile for Waterbury > |
|
Bodycote Thermal Processing - Melrose Park, Illinois Bodycote Thermal Processing 1975 North Ruby Street Melrose Park IL 60160 Illinois |
| Tel: +1 708 344 4080 Fax: +1 708 344 4010 |
| E-Mail: nicholas.bugliarello@bodycote.com |
| Main Contacts |
| Mr Nick Bugliarello, General Manager nicholas.bugliarello@bodycote.com |
| Mr Dennis Lynch, Plant Manager dennis.lynch@bodycote.com |
| Mr John Laffoon, Quality Manager john.laffoon@bodycote.com |
| Mr Dan Schreck, Sales Manager daniel.schreck@bodycote.com |
| Ms Lisa Hill, Office Manager lisa.hill@bodycote.com |
| Mr Chris Chew, Regional Sales Manager, Central Group chris.chew@bodycote.com |
| Ms Angela Eberle, Customer Service Manager angela.eberle@bodycote.com |
| Click here for Applications and the Plant Profile for Melrose Park > |
|
Bodycote Thermal Processing - Indianapolis, Indiana Bodycote Thermal Processing 500 West 21st Street Indianapolis IN 46202 Indiana |
| Tel: +1 317 924 4321 Fax: +1 317 924 1703 |
| E-Mail: kevin.mccurdy@bodycote.com |
| Main Contacts |
| M Kevin McCurdy, Sr. General Manager kevin.mccurdy@bodycote.com |
| Mr Merrill Miller, Quality Manager merrill.miller@bodycote.com |
| John Hillenbrand, Sales john.hillenbrand@bodycote.com |
| Scott Calardo, Regional Operations Manager scott.calardo@bodycote.com |
| Tom Metsch, Office Manager tom.metsch@bodycote.com |
| Mr Chris Chew, Regional Sales Manager, Central Group chris.chew@bodycote.com |
| Click here for Applications and the Plant Profile for Indianapolis > |
|
Bodycote Thermal Processing - Ipswich, Massachusetts Bodycote Thermal Processing 11C Old Right Road Ipswich MA 01938 Massachusetts |
| Tel: +1 978 356 3818 Fax: +1 978 356 0583 |
| E-Mail: mike.sakelakos@bodycote.com |
| Main Contacts |
| Mr Michael Sakelakos, General Manager mike.sakelakos@bodycote.com |
| Mr Colin Misquita, Quality Manager colin.misquita@bodycote.com |
| Kevin Acheson, Sales Manager kevin.acheson@bodycote.com |
| Marion DeRusha, Office Manager marion.derusha@bodycote.com |
| Mr Dennis Smith, Regional Operations Manager dennis.smith@bodycote.com |
| Click here for Applications and the Plant Profile for Ipswich > |
|
Bodycote Thermal Processing - Worcester, Massachusetts Bodycote Thermal Processing 284 Grove Street Worcester MA 01605 Massachusetts |
| Tel: +1 508 754 1724 Fax: +1 508 791 0816 |
| E-Mail: imad.jaber@bodycote.com |
| Main Contacts |
| Mr. Dale Roemer, Sales Manager dale.roemer@bodycote.com |
| Mr Imad Jaber, General Manager imad.jaber@bodycote.com |
| Mr Imad Farhat, Quality Assurance Manager imad.farhat@bodycote.com |
| Mr Peter Grant, Office Manager peter.grant@bodycote.com |
| Mr Vincent Schwartz, Customer Service vincent.schwartz@bodycote.com |
| Mr Dennis Smith, Regional Operations Manager dennis.smith@bodycote.com |
| Click here for Applications and the Plant Profile for Worcester > |
|
Bodycote Thermal Processing - Canton, Michigan Bodycote Thermal Processing 8468 Ronda Drive Canton MI 48187 Michigan |
| Tel: +1 734 459 8514 Fax: +1 734 459 8795 |
| E-Mail: steve.richardson@bodycote.com |
| Main Contacts |
| Mr Stephen Richardson, General Manager steve.richardson@bodycote.com |
| Mr Evin Hutton, Regional Operations Manager evin.hutton@bodycote.com |
| Mr Brett Burns, Plant Manager brett.burns@bodycote.com |
| Mrs Karin Malila, Office Manager karin.malila@bodycote.com |
| Click here for Applications and the Plant Profile for Canton > |
|
Bodycote Thermal Processing - Eden Prairie, Minnesota Bodycote Thermal Processing 10150 Crosstown Circle Eden Prairie MN 55344 Minnesota |
| Tel: +1 952 944 5500 Fax: +1 952 944 8847 |
| E-Mail: robert.manhatton@bodycote.com |
| Main Contacts |
| Mr Bob Manhatton, General Manager robert.manhatton@bodycote.com |
| Mr Jonathan Souer, Quality Manager jonathan.souer@bodycote.com |
| Mr Phil Johnson, Sales phil.johnson@bodycote.com |
| Mr Mel Kreiman, Office Manager mel.kreiman@bodycote.com |
| Mr Mark Lindstrom, Customer Service mark.lindstrom@bodycote.com |
| Mr Chris Chew, Regional Sales Manager, Central Group chris.chew@bodycote.com |
| Click here for Applications and the Plant Profile for Eden Prairie > |
|
Bodycote Thermal Processing - Laconia, New Hampshire Specializes in firearm component heat treating. License available. Bodycote Thermal Processing 187 Water Street Laconia NH 03246 New Hampshire |
| Tel: +1 603 524 7886 Fax: +1 603 524 7432 |
| E-Mail: thomas.ruglic@bodycote.com |
| Main Contacts |
| Mr Thomas Ruglic, General Manager thomas.ruglic@bodycote.com |
| Mr Guy Kemble, Plant Manager guy.kemble@bodycote.com |
| Mr Dennis Smith, Regional Operations Manager dennis.smith@bodycote.com |
| Mr Bruce Steadman, Quality Manager bruce.steadman@bodycote.com |
| Ms Pauline Hill, Office Manager / Customer Service pauline.hill@bodycote.com |
| Mr Kevin Acheson, Sales Manager kevin.acheson@bodycote.com |
| Click here for Applications and the Plant Profile for Laconia > |
|
Bodycote Thermal Processing - Rochester, New York Bodycote Thermal Processing 620 Buffalo Road Rochester NY 14611 New York |
| Tel: +1 585 436 7876 Fax: +1 585 436 5276 |
| E-Mail: anthony.schaut@bodycote.com |
| Main Contacts |
| Mr Anthony Schaut - PE, General Manager anthony.schaut@bodycote.com |
| Mr John Smith, Production Manager john.smith@bodycote.com |
| Ms Bridget Thomas, Office Manager bridget.thomas@bodycote.com |
| Click here for Applications and the Plant Profile for Rochester > |
|
Bodycote Thermal Processing - Cincinnati, Ohio Bodycote Thermal Processing 710 Burns Street Cincinnati OH 45204 Ohio |
| Tel: +1 513 921 2300 Fax: +1 513 921 2536 |
| E-Mail: kevin.mccurdy@bodycote.com |
| Main Contacts |
| Mr Kevin McCurdy, Sr. General Manager / Metallurgical Engineer kevin.mccurdy@bodycote.com |
| Mr Pete Putthoff, Plant Manager pete.putthoff@bodycote.com |
| Mr Roger Dunn, Quality Assurance Manager roger.dunn@bodycote.com |
| Brandon Zembrodt, Sales brandon.zembrodt@bodycote.com |
| Mr John Finn, Customer Service Manager john.finn@bodycote.com |
| Mr Tom Metsch, Office Manager tom.metsch@bodycote.com |
| Mr Roger Fabian, Regional Sales Manager, Central Group roger.fabian@bodycote.com |
| Mr Dennis Smith, Regional Operations Manager dennis.smith@bodycote.com |
| Click here for Applications and the Plant Profile for Cincinnati > |
|
Bodycote Thermal Processing - Highland Heights, Ohio Bodycote Thermal Processing 5475 Avion Park Drive Highland Heights Cleveland OH 44143 Ohio |
| Tel: +1 440 473 2020 Fax: +1 440 473 0947 |
| E-Mail: ron.perkins@bodycote.com |
| Main Contacts |
| Mr Ronald Perkins, General Manager ron.perkins@bodycote.com |
| Ms Lynn Phillips, Sales Associate lynn.phillips@bodycote.com |
| Ms Kelly Phillips, Office Manager kelly.phillips@bodycote.com |
| Click here for Applications and the Plant Profile for Highland Heights > |
|
Bodycote Thermal Processing - Oklahoma City, Oklahoma The Oklahoma City plant specializes in low, medium and high volume production including nitriding, normalising, vacuum heat treating, stress relieving, ferritize annealing, carburizing, FNC and neutral hardening. These are some of the services offered here. Please see the list below for more details and contact us with any questions. Bodycote Thermal Processing 6924 South Eastern Avenue Oklahoma City OK 73149 Oklahoma |
| Tel: +1 405 670 5710 Fax: +1 405 672 3306 |
| E-Mail: chris.johnson@bodycote.com |
| Main Contacts |
| Mr Chris Johnson, General Manager chris.johnson@bodycote.com |
| Mr Jim Bodine, Salesperson jim.bodine@bodycote.com |
| Mr Jeff Windschitl, Regional Sales Manager jeff.windschitl@bodycote.com |
| Ms Amber Harris, Office Manager amber.harris@bodycote.com |
| Click here for Applications and the Plant Profile for Oklahoma City > |
|
Bodycote Thermal Processing - Tulsa (74th St.), Oklahoma Bodycote Thermal Processing 4208 South 74th East Avenue Tulsa OK 74145 Oklahoma |
| Tel: +1 918 627 7324 Fax: +1 918 627 0008 |
| E-Mail: dan.odell@bodycote.com |
| Main Contacts |
| Mr Dan O'Dell, General Manager dan.odell@bodycote.com |
| Mrs Pam Scott, Quality Assurance Manager pam.scott@bodycote.com |
| Ms Molly Pogue, Office Manager molly.pogue@bodycote.com |
| Mr Jeff Windschitl, Regional Sales Manager jeff.windschitl@bodycote.com |
| Click here for Applications and the Plant Profile for Tulsa (74th St.) > |
|
Bodycote Thermal Processing - Tulsa (Pine St.), Oklahoma Bodycote Thermal Processing 1520 North 170th East Avenue Tulsa OK 74116 Oklahoma |
| Tel: +1 918 627 7324 Fax: +1 918 437 9460 |
| E-Mail: dan.odell@bodycote.com |
| Main Contacts |
| Mr Dan Odell, General Manager dan.odell@bodycote.com |
| Mr Kevin Hazleton, Plant Manager kevin.hazleton@bodycote.com |
| Mrs Pam Scott, Quality Assurance Manager pam.scott@bodycote.com |
| Ms Melva Pogue, Office Manager kay.pogue@bodycote.com |
| Mr Jeff Windschitl, Regional Sales Manager jeff.windschitl@bodycote.com |
| Click here for Applications and the Plant Profile for Tulsa (Pine St.) > |
|
Bodycote Thermal Processing - Newmarket, Ontario Bodycote Thermal Processing PO Box 327 630 Newpark Boulevard Newmarket Ontario L3X 2S2 Ontario |
| Tel: +1 905 853 2500 Fax: +1 905 895 7889 |
| E-Mail: gary.prattis@bodycote.com |
| Main Contacts |
| Mr Gary Prattis, General Manager gary.prattis@bodycote.com |
| Ms Heather Battiston, Office Manager heather.battiston@bodycote.com |
| Mr Gary Verhaaff, Operations Support Manager gary.verhaaff@bodycote.com |
| Mr Steve Cropper, Sales Associate steve.cropper@bodycote.com |
| Click here for Applications and the Plant Profile for Newmarket > |
|
Bodycote Metroplex - Arlington (Metroplex), Texas Bodycote Metroplex provides a full range of thermal processes and secondary operations that include: * Controlled Atmosphere heat treatment utilizing batch, pusher, continuous and pit furnace capabilities * Vacuum heat treatment utilizing VFS and Ipsen technologies up to 2-bar capability * Induction heat treatment with 10Khz up to 450Khz controlled scanners * Flame Hardening Capabilities * Ion Nitriding utilizing Seco-Warwick, Klock and VFS technologies * Open Fire Carbottom treatment * Hydrogen Humpback treatment utilizing Thermal Basics and CI Hayes technologies * Secondary operations include Magnetic Particle Inspection, Surface Grinding, Straightening and metallurgical laboratory The plant does not hold any major accreditations at this time. Bodycote Metroplex 428 Dodson Lake Drive Arlington TX 76012 Texas |
| Tel: +1 817.265.5878 Fax: +1 817.860.2718 |
| E-Mail: sales@metroplexht.com |
| Main Contacts |
| Mr Lewis Lance, General Manager lewis.lance@bodycote.com |
| Mr Greg Gabbert, Sales greg.gabbert@bodycote.com |
| Mr Jack Stevens, Production Manager jack.stevens@bodycote.com |
| Ms Paula Parker, Admin - A/P paula.parker@bodycote.com |
| Mr Richard Walsh, Quality/Production, Aerospace richard.walsh@bodycote.com |
| Click here for Applications and the Plant Profile for Arlington (Metroplex) > |
|
Bodycote Thermal Processing - Fort Worth, Texas Bodycote Thermal Processing 2005 Montgomery Street Fort Worth TX 76107 Texas |
| Tel: +1 817 737 6651 Fax: +1 817 377 9610 |
| E-Mail: ilya.soroka@bodycote.com |
| Main Contacts |
| Ilya Soroka, General Manager ilya.soroka@bodycote.com |
| Rick Fleming, Plant Manager rick.d.fleming@bodycote.com |
| Mr Luis Lavarreda, Sales luis.lavarreda@bodycote.com |
| Jeff Windschitl, Regional Sales Manager jeff.windschitl@bodycote.com |
| Click here for Applications and the Plant Profile for Fort Worth > |
|
Bodycote Thermal Processing - Houston-Robertson, Texas Bodycote Thermal Processing 4201 Robertson St Houston TX 77009 Texas |
| Tel: +1 713 691 4544 Fax: +1 713 691 1923 |
| E-Mail: steven.cargill@bodycote.com |
| Main Contacts |
| Mr Steven Cargill, General Manager steven.cargill@bodycote.com |
| Ms Cyndy Ward, Office Manager cyndy.ward@bodycote.com |
| Mr David Sullinger, Plant Manager david.sullinger@bodycote.com |
| Ms Pam Dolan, Customer Service pam.dolan@bodycote.com |
| Mr Jeff Windschitl, Regional Sales Manager jeff.windschitl@bodycote.com |
| Click here for Applications and the Plant Profile for Houston-Robertson > |
|
Bodycote Thermal Processing - New Berlin, Wisconsin Bodycote Thermal Processing 16167 West Rogers Drive New Berlin WI 53151 Wisconsin |
| Tel: +1 262 782 5553 Fax: +1 262 782 5660 |
| E-Mail: don.giessel@bodycote.com |
| Main Contacts |
| Mr Don Giessel, General Manager don.giessel@bodycote.com |
| Ms JoAnne Bruning, Sales Manager joanne.bruning@bodycote.com |
| Mr Chris Chew, Regional Sales Manager chris.chew@bodycote.ccom |
| Ms Pam Schoedl, Office Manager pam.schoedl@bodycote.com |
| Click here for Applications and the Plant Profile for New Berlin > |
|
Bodycote Thermal Processing - Sturtevant, Wisconsin Bodycote Thermal Processing 7316 Durand Avenue Sturtevant WI 53177 Wisconsin |
| Tel: +1 262 554 8770 Fax: +1 262 554 6188 |
| E-Mail: kevin.strom@bodycote.com |
| Main Contacts |
| Mr Kevin Strom, General Manager kevin.strom@bodycote.com |
| Mr. David Zawis, Quality Manager david.zawis@bodycote.com |
| Ms JoAnne Bruning, Salesperson joanne.bruning@bodycote.com |
| Ms Pam Hart, Office Manager/Inside Sales pamela.hart@bodycote.com |
| Mr Robert Struebing, Customer Service - Vacuum robert.struebing@bodycote.com |
| Mr Gary Solfest, Customer Service - Induction gary.solfest@bodycote.com |
| Mr Chris Chew, Regional Sales Manager, Central Group chris.chew@bodycote.com |
| Mr Scott Calardo, Regional Operations Manager scott.calardo@bodycote.com |
| Click here for Applications and the Plant Profile for Sturtevant > |
|